› (号外政府調達第 ™š™ 号) 報 官 月曜日 平成 ™š 年 ˜™ 月 ˜™ 日 3 説明書の交付 本公表に基づき応募する供給 者に対して導入説明書を交付する。 \ 交付期間 平成23年12月12日から平成24年 1月20日まで。 ] 交付場所 上記2]に同じ。 4 説明会の開催 本公表に基づく導入説明会を 開催する。 \ 開催日時 平成23年12月19日10時00分 ] 開催場所 東北大学未来科学技術共同研究 センター1階小会議室 5 その他 この導入計画の詳細は導入説明書に よる。なお、本公表内容は予定であり、変更す ることがあり得る。 6 Summary \ Classification of the products to be procured : 12 ] Nature and quantity of the products to be purchased : Wafer Handling System 1 Set ^ Type of the procurement : Purchase _ Basic requirements of the procurement : A Wafer Bonding Unit a The wafer-bonding unit is required to have capabilities of, that transfer the topography silicon wafer and glass support separately, that spin-coat adhesive on either the silicon wafer or glass support, and that can bond the silicon wafer to glass support. b The wafer-bonding unit is required to consist of the transfer unit and the process unit. Moreover, the process unit is required to consist of separate units ; spin coating, bake, TTV measurement, pre-alignment, alignment and bonding unit. c The process wafer sizes at the waferbonding unit are both φ200¤ and φ 300¤. d The adhesive, that has thermal stability for solder reflow process and has chemical stability against polar base solvent, is required to be used. e The spin coating unit is required to have pre-wet and edge rinse function. f Thickness of adhesive is required to cover from 5μm to 120μm. The wafer-bonding unit is required to have more than 6 of bake unit. h The wafer-bonding unit is required to measure the adhesive thickness by non-contacting method (Also, required for mapping). i The wafer-bonding unit is required to have pre-alignment unit and alignment unit (XY : ±0.1¤, θ : ±0.1°) that are processed before bonding process. j Bonding unit is required to have the bonding capability within 50∼250℃ temperature range and vacuum below 10Pa. B The Wafer debonding unit a The wafer debonding unit is required to have capabilities of, that transfer the thinned silicon wafer, mounted to tape frame and bonded to glass support, that debond the glass support and the debonding method has no mechanical, thermal force or low wavelength area of ultra violate lay, which is possible to impact the wafer device performance. b The wafer debonding unit is required to consist of the transfer unit and the debonding process unit. c The process wafer sizes at the waferbonding unit are both φ200¤ and φ 300¤. d The debonding unit is required to include the collecting station of postdebonded glass support. e The wafer debonding-unit is required to have the transfer tact time as <300sec at 100μm adhesive thickness (>12 wafer per hour). f The debonded thinned wafer need to be crack or chipping free. g The solvent, containing the <1ppm impurity level, is required to be used. h The wafer debonding unit is required to have a unit that can chemically clean the thinned wafer mounted to tape frame for the post-debonding step. g Also, the chemical cleaning process is required to not damage (Dissolve, Swell) to the dicing tape of PVC. i No adhesive residue on the thinned wafer surface after chemical cleaning is required. j The wafer positioning is required as frame alignment and also wafers alignment. ` Time limit for the submission of the requested material : 5 : 00 PM 20, January, 2012 a Contact point for the notice : Higuchi Hideki, Procurement Section, Finance Department, Tohoku University, 2`1`1 Katahira Aoba-ku Sendai-shi 980`8577 Japan, TEL 022`217`4869 資料提供招請に関する公表 次のとおり物品の導入を予定していますので、 当該導入に関して資料等の提供を招請します。 平成 23 年 12 月 12 日 国立大学法人東北大学理事 植木 俊哉 ◎調達機関番号 415 ◎所在地番号 04 〇第6号 1 調達内容 \ 品目分類番号 12 ] 導入計画物品及び数量 ウェハ研磨装置 一式 ^ 調達方法 購入等 _ 導入予定時期 平成24年度5月以降 ` 調達に必要とされる基本的な要求要件 A φ300¤ウェーハの対応 φ200¤とφ 300¤ウェーハの兼用仕様であり、研削、 化学的機械研磨(CMP)、高い清浄度で洗 浄、エッジトリミングを行うことが可能で あること。 B 構成 粗研削軸(Z1) 、仕上げ研削軸 (Z2) 、CMP軸(Z3) 、CMPの仕上 げ研磨軸(Z4)の4軸構成であること C 洗浄機能 以下薬液が使用可能なこと。 アルカリ薬液(SC`1) 、酸薬液(ク エン酸) 、オゾン水 また、ウェーハ表面(加工面)はPVA 製のブラシ洗浄が出来る機構を備えている こと。 D パーティクル対策 筐体にULPAフィ ルタ内蔵のFFU(ファンフィルタユニッ ト)が設置されていること。 E ワーク搬送可能厚さ 最 大 1 5 ¤ 以 上 の • 総厚のワークが搬送可能であること。 F 非接触厚さ測定機構 研削中のウェーハ の厚さを非接触にて測定できること。 G 加工負荷制御 圧力センサを用いてCM P時の接触負荷を制御する加工方式を用い て い る こ と。 知 可 能 荷 重 範 囲 0 ∼ (検 2 000N程度) ¶ H チャックテーブル 水冷式の冷却機構を 採用していること。 I 搬送アームのクランプ バキューム方式 ではなく、 エッジクランプ方式であること。 また、搬送中加工面を乾かさないよう純水 によるウエット搬送が行えること。 J エッジトリミング機構 a 貼り合わせ前後のウェーハのエッジト リミングが可能であること。 b 加工後にオゾン洗浄が可能なシステム であること。 c ハーフカットダイシングも可能である こと。 d φ300¤のウェーハからφ200¤にリサ イズ加工が可能なこと。 K スラリーの対応 以下品種のスラリーに 対応していること。 組成 アルカリ、有機アルカリ、砥粒 シリカ 2 資料及びコメントの提供方法 上記1]の物 品に関する一般的な参考資料及び同`の要求要 件等に関するコメント並びに提供可能なライブ ラリーに関する資料等の提供を招請する。 \ 資料等の提供期限 平成24年1月20日17時 00分(郵送の場合は必着のこと。 ) ] 提供先 〒980`8577 仙台市青葉区片平 2`1`1 東北大学財務部資産・調達管理 課調達管理第二係長 樋口 秀樹 電話 022`217`4869 3 説明書の交付 本公表に基づき応募する供給 者に対して導入説明書を交付する。 \ 交付期間 平成23年12月12日から平成24年 1月20日まで。 ] 交付場所 上記2]に同じ。